Products - Infra Set KZN

Infra Set offers a large range of pipes readily available in nominal lengths of 2.44 and 2.5m. SC (Stormwater Culvert) pipes are supllied with a non-watertight, interlocking ogee joint.

Infra Set supplies pipes that bear the SANS mark and are tested in accordance with SANS 677.

For details of pipes from any particular factory, please contact our sales office. All dimensions in mm.

OG Class 50D – SABS 677 Type SC
Nominal Diameter	Inside diameter	Outside diameter	Wall thickness	Socket depth	Mass	Proof load
(mm)	(ID mm)	(OD mm)	(T mm)	(S mm)	(kg/Unit)	(kN/m)
300	308	368	30	13	210	15.0
375	388	460	36	14	318	18.8
450	460	536	38	15	440	22.5
525	523	629	53	15	620	26.3
600	614	700	43	24	620	30.0
675	685	795	55	25	860	33.8
750	760	874	57	27	940	37.5
825	832	952	60	27	1080	41.3
900	915	1035	60	30	1236	45.0
1050	1030	1185	78	31	1800	52.5
1200	1170	1340	85	33	2360	60.0
1350	1300	1500	100	36	2029	67.5
1500	1460	1670	105	40	3580	75.0
1650	1585	1830	123	40	4440	82.5
1800	1735	2003	134	42	5090	90.0

OG Class 75D – SABS 677 Type SC
Nominal Diameter	Inside diameter	Outside diameter	Wall thickness	Socket depth	Mass	Proof load
(mm)	(ID mm)	(OD mm)	(T mm)	(S mm)	(kg/Unit)	(kN/m)
300	308	368	30	13	210	22.5
375	388	460	36	14	318	28.1
450	460	536	38	15	459	33.8
525	459	629	40	15	635	39.4
600	600	700	50	24	620	45.0
675	685	795	55	25	950	50.6
750	738	874	68	27	1100	56.3
825	800	952	76	27	1373	61.9
900	880	1035	78	30	1540	67.5
1050	1030	1185	78	31	1850	78.8
1200	1143	1340	99	33	2740	90.0
1350	1280	1500	110	36	3240	101.3
1500	1420	1670	125	40	4200	112.5
1650	1585	1830	123	40	4520	123.8
1800	1735	2003	134	42	5426	135.0

OG Class 100D – SABS 677 Type SC
Nominal Diameter	Inside diameter	Outside diameter	Wall thickness	Socket depth	Mass	Proof load
(mm)	(ID mm)	(OD mm)	(T mm)	(S mm)	(kg/Unit)	(kN/m)
225	216	280	32	12	160	22.5
300	308	368	30	13	210	30.0
375	380	460	40	14	394	37.5
450	460	536	38	15	381	45.0
525	523	629	53	15	614	52.5
600	574	700	63	24	852	60.0
675	669	795	63	25	975	67.5
750	738	874	68	27	1154	75.0
825	794	952	79	27	1596	82.5
900	860	1035	88	30	1738	90.0
1050	991	1185	97	31	2205	150.0
1200	1120	1340	110	33	2810	120.0
1350	1250	1500	125	36	3540	135.0
1500	1400	1670	135	40	4282	150.0
1650	1525	1830	153	40	5278	165.0
1800	1640	2003	182	42	6811	180.0

Heavy Duty ‘D’ load pipes for deep fills
Nominal Diameter	Pipe class	Actual internal diameter	Outside diameter	Wall thickness	Lengths	Mass per meter	Total mass per length
		(mm)	(mm)	(mm)	(m)
450	200D	382	526	72	2.50	266	665
600	150D	524	684	80	2.50	387	968
600	200D	494	684	95	2.50	451	1128
750	150D	680	870	95	2.50	589	1473
750	200D	620	870	125	2.50	754	1885
900	150D	810	1040	115	2.50	865	2163
900	200D	750	1040	145	2.50	1046	2615
1050	150D	930	1200	135	2.50	1150	2875
1050	200D	890	1200	155	2.50	1305	3263
1200	150D	1090	1380	145	2.50	1433	3583
1200	200D	1030	1380	175	2.50	1698	4245
1350	150D	1220	1550	165	2.50	1831	4578
1350	200D	1160	1550	195	2.50	2129	5322
1500	150D	1335	1695	180	2.50	2200	5500
1500	200D	1285	1695	205	2.50	2462	6155
2500	150D	2350	2950	300	2.00	6500	13000

NOTE:

125D if required will have the same dimensions as 150D
175D if required will have the same dimensions as 200D

The sewer and irrigation (SI) pipes are manufactured using dolomitic aggregates and have a watertight Spigot and Socket or In-the-Wall joint. Spigot and Socket joint pipes are joined and sealed using either a rolling rubber or a sliding rubber ring respectively. The sliding rubber ring is installed using a soft soap lubricant.

S & S Class 50D – SABS 677 Type SC or SI
Nominal Diameter	Inside diameter	Outside diameter	Wall thickness	Socket diameter	Socket length	Socket depth	Mass	Proof load
(mm)	(ID mm)	(OD mm)	(T mm)	(mm)	(mm)	(S mm)	(kg/Unit)	(kN/m)
375	369	445	38	540	235	127	356	18.8
450	445	533	44	641	257	127	500	22.5
525	514	616	51	730	263	131	659	26.3
600	599	699	50	826	295	138	755	30.0
675	685	787	51	920	318	139	883	33.8
750	762	870	54	1016	329	139	1046	37.5
825	818	946	64	1086	329	139	1295	41.3
900	913	1041	64	1194	363	139	1452	45.0
1050	1034	1194	80	1352	391	162	2026	52.5
1200	1187	1365	89	1543	424	168	2566	60.0
1350	1328	1524	98	1708	442	175	2913	67.5
1500	1491	1689	99	1886	486	190	3300	75.0
1500*	1500	7740	120	1947	490	190	4460	75.0
1800*	1750	2016	133	2180	260	190	5530	90.0

* Vertical cast

S & S Class 75D – SABS 677 Type SC or SI
Nominal Diameter	Inside diameter	Outside diameter	Wall thickness	Socket diameter	Socket length	Socket depth	Mass	Proof load
(mm)	(ID mm)	(OD mm)	(T mm)	(mm)	(mm)	(S mm)	(kg/Unit)	(kN/m)
375	369	445	38	540	235	127	356	28.1
450	445	533	44	641	257	127	500	33.8
525	514	616	51	730	263	131	659	39.4
600	585	699	57	826	295	138	837	45.0
675	673	787	57	920	318	139	878	50.6
750	738	870	66	1016	329	139	1041	56.3
825	812	946	67	1086	329	139	1343	51.9
900	869	1041	86	1194	363	139	1837	57.5
1050	1004	1194	95	1352	391	162	2326	78.8
1200	1157	1365	104	1543	424	168	2929	90.0
1350	1292	1524	116	1708	442	175	3400	101.3
1500	1461	1689	114	1886	486	190	3775	112.5
1500*	1500	7740	120	1947	490	190	4460	112.5
1800*	1750	2016	133	2180	260	190	5530	135.0

* Vertical cast

S & S Class 100D – SABS 677 Type SC or SI
Nominal Diameter	Inside diameter	Outside diameter	Wall thickness	Socket diameter	Socket length	Socket depth	Mass	Proof load
(mm)	(ID mm)	(OD mm)	(T mm)	(mm)	(mm)	(S mm)	(kg/Unit)	(kN/m)
** 225	215	295	40	378	150	100	123	22.5
300	292	368	38	464	222	114	277	30.0
375	369	445	38	540	235	127	356	37.5
450	445	533	44	641	257	127	533	45.0
525	514	616	51	730	263	131	659	52.5
600	585	699	57	826	295	138	839	60.0
675	665	787	61	920	318	139	1017	67.5
750	722	870	74	1016	329	139	1338	75.0
825	780	946	83	1086	329	139	1593	82.5
900	869	1041	86	1194	363	139	1837	90.0
1050	986	1194	104	1352	391	162	2502	105.0
1200	1127	1365	119	1543	424	168	3266	120.0
1350	1262	1524	131	1708	442	175	3800	135.0
1500	1419	1689	135	1886	486	190	4372	150.0
1800*	1750	2050	150	2180	260	190	5780	180.0

The sewer and irrigation (SI) pipes are dolomitic aggregates and have a watertight Spigot and Socket or In-the-Wall joint. Spigot and Socket and In-the-Wall joint pipes are joined and sealed using either a rolling rubber or a sliding rubber ring respectively. The sliding rubber ring is installed using a soft soap lubricant.

Pipes ranging from Ø300 to Ø1800 with Interlocking ogee joints, Ø300 to Ø1800 pipes with Spigot and Socket joints and Ø900 to Ø1800 pipes with In-the-Wall joints are all produced in three strength classes.

All pipes bear the SANS mark and are designed, and tested in accordance with SANS 677.

IWJ Class 50D – SABS 677 Type SC
Nominal Diameter	Inside diameter	Outside diameter	Wall thickness	Socket depth	Mass	Proof load
(mm)	(ID mm)	(OD mm)	(T mm)	(S mm)	(Kg/Unit)	(kN/m)
900	900	1100	100	100	1963	45.0
1050	1050	1250	100	100	2300	52.0
1200	1190	1390	100	100	2550	60.0
1500	1500	1720	110	100	3500	75.0
1800	1810	2130	160	150	6375	90.0

IWJ Class 75D – SABS 677 Type SC
Nominal Diameter	Inside diameter	Outside diameter	Wall thickness	Socket depth	Mass	Proof load
(mm)	(ID mm)	(OD mm)	(T mm)	(S mm)	(Kg/Unit)	(kN/m)
900	900	1100	100	100	1963	67.5
1050	1050	1250	100	100	2275	78.8
1200	1150	1390	120	100	3000	90.0
1500	1460	1720	130	100	4075	112.5
1800	1760	2130	185	150	7075	135.0

IWJ Class 100D – SABS 677 Type SC
Nominal Diameter	Inside diameter	Outside diameter	Wall thickness	Socket depth	Mass	Proof load
(mm)	(ID mm)	(OD mm)	(T mm)	(S mm)	(Kg/Unit)	(kN/m)
900	900	1100	100	100	1963	90.0
1050	1050	1250	100	100	2275	150.0
1200	1150	1390	120	100	3000	120.0
1500	1460	1720	130	100	4075	150.0
1800	1760	2130	185	150	7075	180.0
2500*	2350	2950	300	175	16250	250.0

* Also available in 150D

Nominal length 2,5m.
Details of larger diameter pipes available on request.
Dimentions and thus the of the pipes are subject to change without notice.
For details of pipes from any particular factory, please contact our sales office
All dimentions in mm.

Portal Culverts

Technical Data

Infra Set supplies high quality, high performance factory engineered precast concrete culverts for use in a wide range of modern construction and civil engineering projects.

The company expertise combined with years of knowledge and experience enables Infra Set to offer an extensive range of standard culverts.

In addition to their exceptional load bearing capabilities and structural stability, precast concrete culverts require very little or no maintenance at all to exceed the useful life.

Classification of Culverts

Types of culverts

Infra Set offers the full range of S-Class rectangular portal culverts readily available in lengths of 1.2m
Culverts ranging in size from 450mm x 450mm up to 3600mm x 3000mm with Butt-joints are supplied to the relevant S-Class strength requirements. All S-Class portal culverts bear the SANS mark and are tested and supplied in accordance with SANS 986:2006: Precast reinforced concrete culverts. Reinforced concrete bases are available for all S-Class culverts and are easily installed on site to complete a structurally stable engineered unit.

Infra Set also supply jacking box culverts in various sizes and in standard lengths of 1.190m.

Strength of culverts

Precast portal culverts are classified in terms of their crushing strength when subjected to a combination of loading cases involving vertical and horizontal knife edge tests conducted under factory conditions. The proof load test can be defined as a line load that a culvert must resist without the development of crack widths exceeding 0.25mm over a length of 300mm or over two adjacent ribs in ribbed 16 culverts. When required, ultimate load test are also carried out to a magnitude of 25% greater than the applicable proof loads.

Installation conditions

The trench condition occurs when the culvert is placed into a trench cut into natural ground and then backfilled with suitable material.

In the embankment condition the culvert is installed at ground level and is backfilled with suitable material.

Manhole rings and Components

All chamber and shaft sections are available in 250, 500 and 1000mm lengths.
Dimensions and thus the mass of the manholes are subject to change without notice.
For details of manholes from any particular factory, please contact our sales office.
All dimensions in mm.

Cover Slabs
To fit (mm)	Hole D (mm)	Thickness T (mm)	Mass (kg/unit)
1000	560	150	279
1250	560	185	581
1500	560	220	1072
1750	560	220	1495

Ekgangala Slabs
To fit (mm)	Hole D (mm)	Thickness T (mm)	Mass (kg/unit)
750	560	100	69
1000	560	150	269
1250	560	185	571
1500	560	220	1065
1750	560	220	1487

Shaft Section
Internal Diameter (mm)	Wall Thickness (mm)	Mass (kg/500mm unit)
750	55	169

Lids
Heavy and medium duty replacement lids for cast iron frame Extra heavy, heavy and medium duty lids for concrete frame All lids made with a fitted steel band

Frames
All lids fit in concrete frame Extra heavy duty frames made with a steel seatband

Spacers
Description	Thickness T (mm)	Mass (kg/unit)
Round 750 with 560 hole	75	64

Adaptor Slabs
Description	Thickness T (mm)	Mass (kg/unit)
Square 750 with 560 hole	127	184
Round 750 with 560 hole	110	90

Reducer Slabs
To fit (mm)	Reduce to D (mm)	Thickness T (mm)	Mass (kg/unit)
1000	750	150	205
1250	750	185	492
1500	750	220	968
1750	750	220	1393

Valve Chambers

The air valve chamber is a sectionalized structure designed and developed to provide the industry with a high quality, accurate and long-lasting method of erecting chambers. Incorporating specially designed step irons, the chambers are easy to install, can be made watertight and can be erected in hours rather than days.

All units are fitted with lifting sockets to facilitate safe, easy, and effective handling. All units are supplied with interlocking joints.

Section	Dimensions	Length (m)	Mass (kg/unit)	Thickness (mm)
Small Chamber	2000 x 2000	500	1650	*150
Small Roof	2300 x 2300		1850	**150
Medium Chamber	2500 x 3000	500	2230	*150
Medium Roof	2800 x 3300		2660	**150

* Wall thickness
** Roof thickness

The Infra Set Terrace Blok® TB 300/490 system has unique features that firmly establish it as a market leader.

WATERLÖFFEL®

Waterlöffel® is a versatile, interlocking, dry-stack concrete retaining system.

Paving and cobbles

Infra Set supplies a wide range of paving options in numerous shapes, sizes, finishes and strengths, in virtually any colour or multi-colour variant. State-of-the-art plant and computerised concrete batching ensure best-practice production to high quality standards and close tolerances. The range includes Uni-Decor®, Village Cobble®, Classic Cobble™, and G-blok Cobble™, Villa (flagstone) among others, as well as bush-hammered, high-gloss and exposed aggregate finishes.

Versatile range

BUSH STONE

Bush Stone is InfraSet’s way of recreating the nostalgic charm of weathered granite flagstone without the need to despoil the environment in search of the quarried alterna

COTTAGE STONE

Its elegant charm, smooth finish and appealing colours have made the Cottage Stone® paver a favourite in applications as varied as home gardens, shopping malls, office parking,

CRAZ “E”™ G-BLOK™

The Craz“E”™ G-Blok™ paved surface is highly durable because of its strength and load-spreading features.

MASONIQUE

Since its introduction to South Africa, Masonique® has earned an enviable reputation as a state-of-the art paver.

PARKAY

Reversible for alternative textures: exposed aggregate or smooth surfaces.

RUMBLE STONE

Its rustic charm, strongly reminiscent of a romantic bygone age, has made the ‘aged’ Rumblestone® paver a favourite in applications as varied as home gardens, townhouse projects

Bevel Range

BEVEL

The Bevel is a trusted favourite across the paving industry sectors for many years. The Bevel is manufactured in a 50mm thick version only.

CLASSIPAVE – ONLY AVAILABLE IN DURBAN

These precast paving blocks are not only elegant and versatile, but are precision made to such regular tolerances that they can be laid without grouting.

Cobble Stone Range

CLASSIC COBBLE®

Classic Cobble® gives a beautiful small cobblestone effect to paved areas and can be used in conjunction with the Craz”E”® Classic Cobble® which gives a more rustic effect to the cobblestone.

CRAZ “E”® CLASSIC COBBLE®

Craz “E”® Classic Cobble® gives a beautiful small cobblestone effect to paved areas.

VILLAGE COBBLE

InfraSet’s Village Cobble® is a paving stone which in an inimitable way imparts the character of cobbles to the paved area.

YORK COBBLE PAVER

Landscape architects have welcomed the introduction of the York Cobble Paver™ which is ideally suited to large paved surfaces in driveways, parking areas and pedestrian malls in

Flagstone Range

VILLA®

Architects are favouring the contemporary look that flagstone pavers provide.

Interlocker Paving Range

CRAZ“E”® G-BLOK®

The Craz“E”® G-Blok® paved surface is highly durable because of its strength and load-spreading features.

G-BLOK®

G-Blok®, the paving surface that will provide a good, durable, load bearing and riding surface, requiring little maintenance.

UNI-DECOR®

Uni-Decor® is increasingly being used by architects and developers who are seeking more pleasing shapes, colours and textures for their buildings and surroundings.

Permeable Paving Range

UNI-ECOLOK

Uni-Ecolok pavers are used on paved surfaces which advance rather than retard water infiltration.

Retaining walls

Infra Set supplies a complete range of retaining wall blocks for all types of cut or fill configurations from basic one metre installations to massive 15m walls in angles from 60˚ to 90˚. Favoured by retaining wall design engineers, professional landscapers and the DIY enthusiast, they are used to secure building platforms on industrial and commercial sites as well as for the establishment of landscaped terracing in retail and domestic environments.

The range includes four retaining wall systems: Loffeslstein, RidgeBlok, TerraceBlok and Waterloffel which enjoy a nationwide reputation for quality and reliability and which come in a variety of finishes and colours to suit differing applications and design preferences.

First introduced in 1989, today our blocks form part of the national landscape in a harmonious blend of the built and natural environments. They can be seen in industrial and office parks, in shopping centres, in housing developments, on freeway embankments, on our beaches and river banks and in attenuation ponds; in fact in any property development application where earthen embankments and building platforms require reliable and attractive erosion control.

INFRABLOK® 350

The Infra Set InfraBlok® 350 retaining block system is unique in its flexibility and aesthetic appeal.

INFRABLOK® 425

The Infra Set InfraBlok® 425 retaining block system is unique in its flexibility and aesthetic appeal.

LÖFFELSTEIN®

Löffelstein® is a dry stacking, interlocking retaining system. It is unique because of its versatility, adaptability and plantability.

RIDGEBLOK

A versatile, structurally sound and robust block.

RidgeBlok is versatile

TERRACE BLOK 190/190 ROCKFACE

The Infra Set Terrace Blok® is a light versatile concrete block which provides the ideal solution for homeowners and DIY enthusiasts wishing to provide support to slopes in

TERRACE BLOK® TB 300

The Infraset Terrace Blok® TB 300 system has unique features that firmly establish it as a market leader.

TERRACE BLOK® TB 300/490

KERBS , CHANNELS , MARKERS AND MORE

Suppliers of quality Precast Products , Kerbs, Channels, Wash Trough , Gulley, Septic Tanks, Markers, Bollards, Stadium Seating